Toyota Avalon (XX50): Power Window Regulator Motor(for Front Door)

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Vehicle Exterior / Window / Glass / Power Window Regulator Motor(for Front Door)

Components

COMPONENTS

ILLUSTRATION

*A	for HV Model	-	-
*1	LUGGAGE TRIM SERVICE HOLE COVER	-	-

ILLUSTRATION

*A	for Driver Side	*B	for Front Passenger Side
*1	COURTESY LIGHT ASSEMBLY	*2	FRONT DOOR ARMREST COVER SUB-ASSEMBLY
*3	FRONT DOOR TRIM BOARD SUB-ASSEMBLY	*4	FRONT DOOR TRIM POCKET COVER
*5	MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL	*6	POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL

ILLUSTRATION

*1	FRONT DOOR GLASS SUB-ASSEMBLY	*2	FRONT DOOR INNER GLASS WEATHERSTRIP
*3	FRONT DOOR SERVICE HOLE COVER	*4	FRONT DOOR TRIM BRACKET
*5	FRONT DOOR VENT SEAL	*6	FRONT DOOR WINDOW REGULATOR ASSEMBLY
*7	POWER WINDOW REGULATOR MOTOR ASSEMBLY	*8	FRONT DOOR WEATHERSTRIP CLIP
*9	FRONT DOOR NO. 2 SERVICE HOLE COVER	*10	HOLE PLUG
	Nm (kgfcm, ft.*lbf): Specified torque		MP grease

Inspection

INSPECTION

PROCEDURE

1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

(a) Connect a positive (+) lead from the auxiliary battery to connector terminal 2.

NOTICE:

Do not connect a positive (+) lead from the auxiliary battery to any terminal other than terminal 2 to avoid damaging the pulse sensor inside the motor.

*a	Component without harness connected (Power Window Regulator Motor Assembly (for Driver Door))
*b	Clockwise
*c	Counterclockwise
*d	Motor gear

(b) Connect a negative (-) lead from the auxiliary battery to connector terminals 1 and 7 or 10.

OK:

Measurement Condition	Specified Condition
Connect a positive (+) lead from the auxiliary battery to terminal 2, connect a negative (-) lead from the auxiliary battery to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) lead from the auxiliary battery to terminal 10.	Motor gear rotates clockwise
Connect a positive (+) lead from the auxiliary battery to terminal 2, connect a negative (-) lead from the auxiliary battery to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) lead from the auxiliary battery to terminal 7.	Motor gear rotates counterclockwise

If the result is not as specified, replace the power window regulator motor assembly (for driver door).

CAUTION:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.

2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR)

(a) Connect a positive (+) lead from the auxiliary battery to connector terminal 2.

NOTICE:

Do not connect a positive (+) lead from the auxiliary battery to any terminal other than terminal 2 to avoid damaging the pulse sensor inside the motor.

*a	Component without harness connected (Power Window Regulator Motor Assembly (for Front Passenger Door))
*b	Clockwise
*c	Counterclockwise
*d	Motor gear

(b) Connect a negative (-) lead from the auxiliary battery to connector terminal 1 and 7 or 10.

OK:

Measurement Condition	Specified Condition
Connect the positive (+) lead from the auxiliary battery to terminal 2, connect a negative (-) lead from the auxiliary battery to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) lead from the auxiliary battery to terminal 10.	Motor gear rotates counterclockwise
Connect a positive (+) lead from the auxiliary battery to terminal 2, connect a negative (-) lead from the auxiliary battery to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) lead from the auxiliary battery to terminal 7.	Motor gear rotates clockwise

If the result is not as specified, replace the power window regulator motor assembly (for front passenger door).

CAUTION:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.

Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor assembly.

(a) Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

Torque:

5.39 N·m {55 kgf·cm, 48 in·lbf}

HINT:

When replacing a power window regulator motor assembly, a new power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

3. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

Click here

4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Click here

5. INSTALL FRONT DOOR VENT SEAL

Click here

6. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

Click here

7. INSTALL FRONT DOOR SERVICE HOLE COVER

Click here

8. INSTALL FRONT DOOR TRIM BRACKET

Click here

9. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

10. INSTALL COURTESY LIGHT ASSEMBLY

Click here

11. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

12. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

13. INSTALL FRONT DOOR TRIM POCKET COVER

Click here

14. INSTALL FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here

15. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FXS:

Click here

for 2GR-FKS:

Click here

16. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

17. INITIALIZE POWER WINDOW CONTROL SYSTEM

for Gasoline Model: Click here

for HV Model: Click here

18. INSPECT POWER WINDOW OPERATION

for Gasoline Model: Click here

for HV Model: Click here

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
		Lighting system (for Gasoline Model with Cornering Light)
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system
Door window regulator assembly Power window regulator motor assembly Front door glass sub-assembly Front door glass run	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
		Lighting system (for HV Model with Cornering Light)
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system
Door window regulator assembly Power window regulator motor assembly Front door glass sub-assembly Front door glass run	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

Click here

2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FXS:

Click here

for 2GR-FKS:

Click here

4. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here

5. REMOVE FRONT DOOR TRIM POCKET COVER

Click here

6. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

8. REMOVE COURTESY LIGHT ASSEMBLY

Click here

9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

10. REMOVE FRONT DOOR TRIM BRACKET

Click here

11. REMOVE FRONT DOOR SERVICE HOLE COVER

Click here

12. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

Click here

13. REMOVE FRONT DOOR VENT SEAL

Click here

14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Click here

15. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

Click here

16. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

(a) Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.

Power Window Master Switch

Power Window Regulator Motor(for Rear Door)

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Seat Belt: Tongue Plate Stopper
ComponentsCOMPONENTS ILLUSTRATION *1 TONGUE PLATE STOPPER - - ● Non-reusable part - - ReplacementREPLACEMENT PROCEDURE 1. REMOVE TONGUE PLATE STOPPER (a) Slide the tongue plate above the installation position of the tongue plate stopper, and temporarily hold it with adhesive tape. *a Adhesive Tap ...