Toyota Avalon (XX50): Power Window Regulator Motor(for Rear Door)

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Vehicle Exterior / Window / Glass / Power Window Regulator Motor(for Rear Door)

Components

COMPONENTS

ILLUSTRATION

*A

for HV Model

-

-

*1

LUGGAGE TRIM SERVICE HOLE COVER

-

-

ILLUSTRATION

*1

REAR DOOR ARMREST COVER SUB-ASSEMBLY

*2

REAR DOOR TRIM ASSEMBLY COVER

*3

REAR DOOR TRIM BOARD SUB-ASSEMBLY

*4

REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

ILLUSTRATION

*1

POWER WINDOW REGULATOR MOTOR ASSEMBLY

*2

REAR DOOR GLASS RUN

*3

REAR DOOR GLASS SUB-ASSEMBLY

*4

REAR DOOR INNER GLASS WEATHERSTRIP

*5

REAR DOOR NO. 1 TRIM BRACKET

*6

REAR DOOR NO. 2 SERVICE HOLE COVER

*7

REAR DOOR REAR GUIDE SEAL

*8

REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

*9

REAR DOOR SERVICE HOLE COVER

*10

REAR DOOR WEATHERSTRIP

*11

REAR DOOR WINDOW REGULATOR ASSEMBLY

*12

HOLE PLUG

*13

REAR DOOR NO. 3 SERVICE HOLE COVER

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

MP grease

Inspection

INSPECTION

PROCEDURE

1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR)

(a) Connect a positive (+) lead from the auxiliary battery to connector terminal 2.

NOTICE:

Do not connect a positive (+) lead from the auxiliary battery to any terminal other than terminal 2 to avoid damaging the pulse sensor inside the motor.

*a

Component without harness connected

(Power Window Regulator Motor Assembly (for Rear LH Door))

*b

Clockwise

*c

Counterclockwise

*d

Motor gear

(b) Connect a negative (-) lead from the auxiliary battery to connector terminal 1 and 7 or 10.

(c) Check that the motor gear rotates smoothly as follows:

OK:

Measurement Condition

Specified Condition
  1. Connect a positive (+) lead from the auxiliary battery to terminal 2, connect a negative (-) lead from the auxiliary battery to terminal 1, and keep them connected for 3 seconds or more.
  2. With terminals 2 and 1 connected, connect a negative (-) lead from the auxiliary battery to terminal 10.

Motor gear rotates clockwise
  1. Connect a positive (+) lead from the auxiliary battery to terminal 2, connect a negative (-) lead from the auxiliary battery to terminal 1, and keep them connected for 3 seconds or more.
  2. With terminals 2 and 1 connected, connect a negative (-) lead from the auxiliary battery to terminal 7.

Motor gear rotates counterclockwise
  • If the result is not as specified, replace the power window regulator motor assembly (for rear LH door).

CAUTION:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.

2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR)

(a) Connect a positive (+) lead from the auxiliary battery to connector terminal 2.

NOTICE:

Do not connect a positive (+) lead from the auxiliary battery to any terminal other than terminal 2 to avoid damaging the pulse sensor inside the motor.

*a

Component without harness connected

(Power Window Regulator Motor Assembly (for Rear RH Door))

*b

Clockwise

*c

Counterclockwise

*d

Motor gear

(b) Connect a negative (-) lead from the auxiliary battery to connector terminals 1 and 7 or 10.

(c) Check that the motor gear rotates smoothly as follows:

OK:

Measurement Condition

Specified Condition
  1. Connect the positive (+) lead from the auxiliary battery to terminal 2, connect a negative (-) lead from the auxiliary battery to terminal 1, and keep them connected for 3 seconds or more.
  2. With terminals 2 and 1 connected, connect a negative (-) lead from the auxiliary battery to terminal 10.

Motor gear rotates counterclockwise
  1. Connect a positive (+) lead from the auxiliary battery to terminal 2, connect a negative (-) lead from the auxiliary battery to terminal 1, and keep them connected for 3 seconds or more.
  2. With terminals 2 and 1 connected, connect a negative (-) lead from the auxiliary battery to terminal 7.

Motor gear rotates clockwise
  • If the result is not as specified, replace the power window regulator motor assembly (for rear RH door).

CAUTION:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.

Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor assembly.

(a) Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

Torque:

5.39 N·m {55 kgf·cm, 48 in·lbf}

HINT:

When replacing a power window regulator motor assembly, a new power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

3. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

Click here

4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Click here

5. INSTALL REAR DOOR REAR GUIDE SEAL

Click here

6. CONNECT REAR DOOR WEATHERSTRIP

(a) Engage the clip and connect the rear door weatherstrip.

7. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

Click here

8. INSTALL REAR DOOR GLASS RUN

Click here

9. INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER

Click here

10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

Click here

11. INSTALL REAR DOOR SERVICE HOLE COVER

Click here

12. INSTALL REAR DOOR NO. 1 TRIM BRACKET

Click here

13. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

14. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

15. INSTALL REAR DOOR TRIM ASSEMBLY COVER

Click here

16. INSTALL REAR DOOR ARMREST COVER SUB-ASSEMBLY

Click here

17. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FXS:

Click here

for 2GR-FKS:

Click here

18. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

19. INITIALIZE POWER WINDOW CONTROL SYSTEM

for Gasoline Model: Click here

for HV Model: Click here

20. INSPECT POWER WINDOW OPERATION

for Gasoline Model: Click here

for HV Model: Click here

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function When Necessary Procedures are not Performed

Link
*: When performing learning using the Techstream.

Click here

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

Pre-collision system

Intelligent clearance sonar system*

Lighting system (for Gasoline Model with Cornering Light)

Memorize steering angle neutral point

Parking assist monitor system

Panoramic view monitor system

  • Door window regulator assembly
  • Rear door glass sub-assembly
  • Power window regulator motor assembly
  • Rear door glass run

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function When Necessary Procedures are not Performed

Link
*: When performing learning using the Techstream.

Click here

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

Pre-collision system

Intelligent clearance sonar system*

Lighting system (for HV Model with Cornering Light)

Memorize steering angle neutral point

Parking assist monitor system

Panoramic view monitor system

  • Door window regulator assembly
  • Rear door glass sub-assembly
  • Rear door glass sub-assembly
  • Rear door glass run

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FXS:

Click here

for 2GR-FKS:

Click here

4. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY

Click here

5. REMOVE REAR DOOR TRIM ASSEMBLY COVER

Click here

6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

8. REMOVE REAR DOOR NO. 1 TRIM BRACKET

Click here

9. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Click here

11. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

Click here

12. REMOVE REAR DOOR GLASS RUN

Click here

13. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

Click here

14. DISCONNECT REAR DOOR WEATHERSTRIP

(a) Disengage the clip and disconnect the rear door weatherstrip until the screws of the rear door rear guide seal is visible.

15. REMOVE REAR DOOR REAR GUIDE SEAL

Click here

16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here

17. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY

Click here

18. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

(a) Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.

Power Window Regulator Motor(for Front Door)

Quarter Window Glass

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Audio And Visual System(for Gasoline Model): Panel Switches do not Function. Parking Brake Switch Circuit. Parts Location
Panel Switches do not Function CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System. Click here When replacing the radio ...

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual

© 2025 Copyright vehicle-exterior.tavalon.net
0.2048