Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After
turning the engine switch (for Gasoline Model) or power switch (for HV
Model) off, waiting time may be required before disconnecting the cable
from the negative (-) auxiliary battery terminal. Therefore, make sure
to read the disconnecting the cable from the negative (-) auxiliary
battery terminal notices before proceeding with work.
Click here
2. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY
 |
Install in this Direction |
(a) Engage the 7 claws to install a new front door belt moulding assembly as shown in the illustration.
3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
Click here
4. INSTALL FRONT DOOR VENT SEAL
Click here
5. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP
Click here
6. INSTALL FRONT DOOR SERVICE HOLE COVER
Click here
7. INSTALL FRONT DOOR TRIM BRACKET
Click here
8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here
9. INSTALL COURTESY LIGHT ASSEMBLY
Click here
10. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here
11. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here
12. INSTALL FRONT DOOR TRIM POCKET COVER
Click here
13. INSTALL FRONT DOOR ARMREST COVER SUB-ASSEMBLY
Click here
14. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
15. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
16. INITIALIZE POWER WINDOW CONTROL SYSTEM
for Gasoline Model:
Click here
for HV Model:
Click here
17. INSPECT POWER WINDOW OPERATION
for Gasoline Model:
Click here
for HV Model:
Click here
Removal
REMOVAL
CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization, or
registration) that must be performed after parts are removed and
installed, or replaced during front door belt moulding assembly
removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here  |
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for Gasoline Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
|
Front door glass sub-assembly | Initialize power window control system |
- Auto up and down function
- Jam protection function
- Remote control function
- Key-linked function
- Wireless transmitter-linked function
- Key-off operation function
- Catch protection function
- Window open warning function
|
|
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for HV Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
|
Front door glass sub-assembly | Initialize power window control system |
- Auto up and down function
- Jam protection function
- Remote control function
- Key-linked function
- Wireless transmitter-linked function
- Key-off operation function
- Catch protection function
- Window open warning function
|
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After
turning the engine switch (for Gasoline Model) or power switch (for HV
Model) off, waiting time may be required before disconnecting the cable
from the negative (-) auxiliary battery terminal. Therefore, make sure
to read the disconnecting the cable from the negative (-) auxiliary
battery terminal notices before proceeding with work.
Click here
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
4. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY
Click here
5. REMOVE FRONT DOOR TRIM POCKET COVER
Click here
6. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here
7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here
8. REMOVE COURTESY LIGHT ASSEMBLY
Click here
9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here
10. REMOVE FRONT DOOR TRIM BRACKET
Click here
11. REMOVE FRONT DOOR SERVICE HOLE COVER
Click here
12. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP
Click here
13. REMOVE FRONT DOOR VENT SEAL
Click here
14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Click here
15. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY
(a) Apply protective tape around the front door belt moulding assembly as shown in the illustration.
 | Protective Tape |
 | Remove in this Direction |
(b) Disengage the 7 claws to remove the front door belt moulding assembly as shown in the illustration.
