Toyota Avalon (XX50): Black Out Tape(for Rear Door)

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Vehicle Exterior / Exterior Panels / Trim / Black Out Tape(for Rear Door)

Components

COMPONENTS

ILLUSTRATION

*A	for HV Model	-	-
*1	LUGGAGE TRIM SERVICE HOLE COVER	-	-

ILLUSTRATION

*1	REAR DOOR ARMREST COVER SUB-ASSEMBLY	*2	REAR DOOR TRIM ASSEMBLY COVER
*3	REAR DOOR TRIM BOARD SUB-ASSEMBLY	*4	REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

ILLUSTRATION

*1	REAR DOOR GLASS RUN	*2	REAR DOOR GLASS SUB-ASSEMBLY
*3	REAR DOOR INNER GLASS WEATHERSTRIP	*4	REAR DOOR NO. 1 TRIM BRACKET
*5	REAR DOOR NO. 2 SERVICE HOLE COVER	*6	REAR DOOR REAR GUIDE SEAL
*7	REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY	*8	REAR DOOR SERVICE HOLE COVER
*9	REAR DOOR WEATHERSTRIP	*10	HOLE PLUG
	Nm (kgfcm, ft.*lbf): Specified torque	-	-

ILLUSTRATION

*1	NO. 1 BLACK OUT TAPE	*2	NO. 2 BLACK OUT TAPE
*3	NO. 3 BLACK OUT TAPE	*4	REAR DOOR CHECK ASSEMBLY
*5	REAR DOOR FRAME GARNISH	*6	REAR DOOR WEATHERSTRIP
	Nm (kgfcm, ft.*lbf): Specified torque	●	Non-reusable part
	Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent	★	Precoated part

Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. REPAIR INSTRUCTION

Click here

3. INSTALL NO. 2 BLACK OUT TAPE

(a) Refer to the illustration to position a new No. 2 black out tape.

*A	Lower Side	*B	LH Side
*C	RH Side	-	-
*1	Rear Door Weatherstrip	-	-
*a	Edge of Curved Surface	*b	Straight
*c	Triangle	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	5.0 mm (0.197 in.)	B	2.5 mm (0.0984 in.)
C	1.0 mm (0.0394 in.)	-	-

(b) Remove the release paper and apply the No. 2 black out tape.

4. INSTALL NO. 3 BLACK OUT TAPE

(a) Refer to the illustration to position a new No. 3 black out tape.

*A	Front Side	*B	LH Side
*C	RH Side	-	-
*a	Rib of Door Frame Garnish	*b	Edge of Curved Surface
*c	Straight	*d	Triangle

Standard Measurement:

Area	Measurement	Area	Measurement
A	8.5 mm (0.335 in.)	B	1.0 mm (0.0394 in.)
C	2.5 mm (0.0984 in.)	-	-

(b) Remove the release paper and apply the No. 3 black out tape.

5. INSTALL NO. 1 BLACK OUT TAPE

(a) Refer to the illustration to position a new No. 1 black out tape.

*A	Upper Side	*B	LH Side
*C	RH Side	-	-
*1	Rear Door Weatherstrip	-	-
*a	Rib of Door Frame Garnish	*b	Edge of Curved Surface
*c	Straight	*d	Triangle

Standard Measurement:

Area	Measurement	Area	Measurement
A	3.0 mm (0.118 in.)	B	5.0 mm (0.197 in.)
C	-1.0 to 1.0 mm (-0.0394 to 0.0394 in.)	D	1.0 mm (0.0394 in.)
E	1.2 mm (0.0472 in.)	F	1.0 mm (0.0394 in.)

(b) Remove the release paper and apply the No. 1 black out tape.

6. INSTALL REAR DOOR FRAME GARNISH

Click here

7. INSTALL REAR DOOR WEATHERSTRIP

Click here

8. INSTALL REAR DOOR CHECK ASSEMBLY

Click here

9. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Click here

10. INSTALL REAR DOOR REAR GUIDE SEAL

Click here

11. CONNECT REAR DOOR WEATHERSTRIP

Click here

12. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

Click here

13. INSTALL REAR DOOR GLASS RUN

Click here

14. INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER

Click here

15. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

Click here

16. INSTALL REAR DOOR SERVICE HOLE COVER

Click here

17. INSTALL REAR DOOR NO. 1 TRIM BRACKET

Click here

18. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

19. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

20. INSTALL REAR DOOR TRIM ASSEMBLY COVER

Click here

21. INSTALL REAR DOOR ARMREST COVER SUB-ASSEMBLY

Click here

22. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FXS:

Click here

for 2GR-FKS:

Click here

23. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

24. INITIALIZE POWER WINDOW CONTROL SYSTEM

for Gasoline Model:

Click here

for HV Model:

Click here

25. INSPECT POWER WINDOW OPERATION

for Gasoline Model:

Click here

for HV Model:

Click here

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane Departure Alert System (w/ Steering Control)
		Pre-collision System
		Intelligent Clearance Sonar System*
		Lighting System (for Gasoline Model with Cornering Light)
	Memorize steering angle neutral point	Parking Assist Monitor System
	Memorize steering angle neutral point	Panoramic View Monitor System
Rear door glass sub-assembly Rear door glass run	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Lane Departure Alert System (w/ Steering Control)
		Pre-collision System
		Intelligent Clearance Sonar System*
		Lighting System (for HV Model with Cornering Light)
	Memorize steering angle neutral point	Parking Assist Monitor System
	Memorize steering angle neutral point	Panoramic View Monitor System
Rear door glass sub-assembly Rear door glass run	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

Click here

2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FXS:

Click here

for 2GR-FKS:

Click here

4. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY

Click here

5. REMOVE REAR DOOR TRIM ASSEMBLY COVER

Click here

6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

8. REMOVE REAR DOOR NO. 1 TRIM BRACKET

Click here

9. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Click here

11. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

Click here

12. REMOVE REAR DOOR GLASS RUN

Click here

13. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

Click here

14. DISCONNECT REAR DOOR WEATHERSTRIP

Click here

15. REMOVE REAR DOOR REAR GUIDE SEAL

Click here

16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here

17. REMOVE REAR DOOR CHECK ASSEMBLY

Click here

18. REMOVE REAR DOOR WEATHERSTRIP

Click here

19. REMOVE REAR DOOR FRAME GARNISH

Click here

20. REMOVE NO. 1 BLACK OUT TAPE

HINT:

When removing the No. 1 black out tape, heat the vehicle body and No. 1 black out tape using a heat light.

Heating Temperature

Item	Temperature
No. 1 Black Out Tape and Vehicle Body	40 to 60°C (104 to 140°F)

CAUTION:

Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.

*a	Heated Part
*b	Heat Light

NOTICE:

Do not heat the vehicle body excessively.

(a) Using a heat light, heat the No. 1 black out tape and vehicle body.

(b) Pull back on one of the ends of the No. 1 black out tape to remove it.

HINT:

When pulling on the No. 1 black out tape, pull it parallel to the vehicle body.

21. REMOVE NO. 3 BLACK OUT TAPE

HINT:

When removing the No. 3 black out tape, heat the vehicle body and No. 3 black out tape using a heat light.

Heating Temperature

Item	Temperature
No. 3 Black Out Tape and Vehicle Body	40 to 60°C (104 to 140°F)

CAUTION:

Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.

*a	Heated Part
*b	Heat Light

NOTICE:

Do not heat the vehicle body excessively.

(a) Using a heat light, heat the No. 3 black out tape and vehicle body.

(b) Pull back on one of the ends of the No. 3 black out tape to remove it.

HINT:

When pulling on the No. 3 black out tape, pull it parallel to the vehicle body.

22. REMOVE NO. 2 BLACK OUT TAPE

HINT:

When removing the No. 2 black out tape, heat the vehicle body and No. 2 black out tape using a heat light.

Heating Temperature

Item	Temperature
No. 2 Black Out Tape and Vehicle Body	40 to 60°C (104 to 140°F)

CAUTION:

Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.

*a	Heated Part
*b	Heat Light

NOTICE:

Do not heat the vehicle body excessively.

(a) Using a heat light, heat the No. 2 black out tape and vehicle body.

(b) Pull back on one of the ends of the No. 2 black out tape to remove it.

HINT:

When pulling on the No. 2 black out tape, pull it parallel to the vehicle body.

Black Out Tape(for Front Door)

Front Bumper

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Sfi System: Problem Symptoms Table. Readiness Monitor Drive Pattern. Registration
Problem Symptoms Table PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by ...