Toyota Avalon (XX50): Washer Nozzle

Adjustment

ADJUSTMENT

PROCEDURE

1. REMOVE WASHER NOZZLE SUB-ASSEMBLY

Click here

2. ADJUST WASHER NOZZLE SUB-ASSEMBLY

(a) Select a washer nozzle sub-assembly so the position the washer fluid hits the windshield will be within the standard area. Replace the washer nozzle sub-assembly with the selected one.

*a

Washer Fluid Spray Angle

*b

Part Number

*c

Right Mark

*d

Left Mark

3. INSTALL WASHER NOZZLE SUB-ASSEMBLY

Click here

Components

COMPONENTS

ILLUSTRATION

*1

WASHER NOZZLE SUB-ASSEMBLY

-

-

Non-reusable part

-

-

Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. INSTALL WASHER NOZZLE SUB-ASSEMBLY

(a) Connect a new washer nozzle sub-assembly to the washer hose.

(b) Engage the 2 claws as indicated by the arrows, in the order shown in the illustration to install the washer nozzle sub-assembly.

Install in this Direction (1)

Install in this Direction (2)

2. INSPECT WASHER NOZZLE SUB-ASSEMBLY

Click here

3. ADJUST WASHER NOZZLE SUB-ASSEMBLY

Click here

On-vehicle Inspection

ON-VEHICLE INSPECTION

PROCEDURE

1. INSPECT WASHER NOZZLE SUB-ASSEMBLY

(a) Operate the washer nozzle sub-assemblies and check the position that the washer fluid contacts the windshield.

Standard:

Center of washer fluid contacts the windshield in the areas shown in the illustration.

HINT:

If the result is not as specified, replace the washer nozzle sub-assembly.

Text in Illustration

*a

Passenger Side Lower Spray (+1°)

*b

Passenger Side Lower Spray (0°)

*c

Passenger Side Lower Spray (-1°)

*d

Driver Side Lower Spray (+1°)

*e

Driver Side Lower Spray (0°)

*f

Driver Side Lower Spray (-1°)

*g

Passenger Side Upper Spray (+1°)

*h

Passenger Side Upper Spray (0°)

*i

Passenger Side Upper Spray (-1°)

*j

Driver Side Upper Spray (+1°)

*k

Driver Side Upper Spray (0°)

*l

Driver Side Upper Spray (-1°)

Removal

REMOVAL

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE WASHER NOZZLE SUB-ASSEMBLY

(a) Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws as shown in the illustration to separate the washer nozzle sub-assembly.

*a

Protective Tape

Remove in this Direction (1)

Remove in this Direction (2)

NOTICE:

Be careful not to damage the windshield glass.

(b) Disconnect the washer hose to remove the washer nozzle sub-assembly.

NOTICE:

Washer nozzle sub-assemblies cannot be reused.

Washer Motor

Wiper And Washer System(for Gasoline Model)

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Meter / Gauge System(for Gasoline Model): Precaution. Problem Symptoms Table. Speed Signal Circuit
Precaution PRECAUTION NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected. System Name See Procedure Lane Departure Alert System (w/ Steering Control) Intelligent Clearance Sonar System Parking Assist Monitor Sy ...

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual

© 2025 Copyright vehicle-exterior.tavalon.net
0.1456