Toyota Avalon (XX50): Outer Rear View Mirror

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Vehicle Exterior / Mirror (ext) / Outer Rear View Mirror

Components

COMPONENTS

ILLUSTRATION

*A	for Driver Side	*B	for Front Passenger Side
*1	COURTESY LIGHT ASSEMBLY	*2	FRONT DOOR ARMREST COVER SUB-ASSEMBLY
*3	FRONT DOOR TRIM BOARD SUB-ASSEMBLY	*4	FRONT DOOR TRIM POCKET COVER
*5	MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL	*6	POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL

ILLUSTRATION

*1	HOLE PLUG	*2	OUTER MIRROR INSTALL HOLE COVER
*3	OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER	-	-
	Nm (kgfcm, ft.*lbf): Specified torque	-	-

ILLUSTRATION

*A	w/ Panoramic View Monitor System	-	-
*1	OUTER MIRROR	*2	OUTER MIRROR COVER
*3	SIDE TELEVISION CAMERA ASSEMBLY	*4	SIDE TURN SIGNAL LIGHT ASSEMBLY
*5	VISOR HOUSING	*6	CAMERA COVER

Disassembly

DISASSEMBLY

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. REMOVE OUTER MIRROR

Click here

2. REMOVE OUTER MIRROR COVER

Click here

3. REMOVE VISOR HOUSING

(a) Move the outer rear view mirror as shown in the illustration.

(b) Using a T20 "TORX" driver, remove the 3 screws.

Remove in this Direction

4. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY

Click here

5. REMOVE SIDE TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)

Click here

Inspection

INSPECTION

PROCEDURE

1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Panoramic View Monitor System)

(a) Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.

(1) Disconnect the outer rear view mirror assembly RH connector.

*a	Component without harness connected (Outer Rear View Mirror Assembly RH)

(2) Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:

Auxiliary Battery Connection	Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MV) Auxiliary battery negative (-) → Terminal 2 (M+)	Turns upward
Auxiliary battery positive (+) → Terminal 2 (M+) Auxiliary battery negative (-) → Terminal 3 (MV)	Turns downward
Auxiliary battery positive (+) → Terminal 1 (MH) Auxiliary battery negative (-) → Terminal 2 (M+)	Turns left
Auxiliary battery positive (+) → Terminal 2 (M+) Auxiliary battery negative (-) → Terminal 1 (MH)	Turns right

If the result is not as specified, replace the outer rear view mirror assembly RH.

(b) Check the operation of the mirror heater.

(1) Disconnect the outer rear view mirror assembly RH connector.

*a	Component without harness connected (Outer Rear View Mirror Assembly RH)

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
5 (+) - 6 (-)	25°C (77°F)	10 to 17 Ω

If the result is not as specified, replace the outer rear view mirror assembly RH.

(3) Connect a cable from the positive (+) auxiliary battery terminal to terminal 5 and the negative (-) auxiliary battery terminal to terminal 6, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.

OK:

Mirror becomes warm.

If the result is not as specified, replace the outer rear view mirror assembly RH.

2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Panoramic View Monitor System)

(a) Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.

(1) Disconnect the outer rear view mirror assembly RH connector.

*a	Component without harness connected (Outer Rear View Mirror Assembly RH)

(2) Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:

Auxiliary Battery Connection	Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MV) Auxiliary battery negative (-) → Terminal 2 (M+)	Turns upward
Auxiliary battery positive (+) → Terminal 2 (M+) Auxiliary battery negative (-) → Terminal 3 (MV)	Turns downward
Auxiliary battery positive (+) → Terminal 1 (MH) Auxiliary battery negative (-) → Terminal 2 (M+)	Turns left
Auxiliary battery positive (+) → Terminal 2 (M+) Auxiliary battery negative (-) → Terminal 1 (MH)	Turns right

If the result is not as specified, replace the outer rear view mirror assembly RH.

(b) Check the operation of the mirror heater.

(1) Disconnect the outer rear view mirror assembly RH connector.

*a	Component without harness connected (Outer Rear View Mirror Assembly RH)

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
5 (+) - 6 (-)	25°C (77°F)	10 to 17 Ω

If the result is not as specified, replace the outer rear view mirror assembly RH.

(3) Connect a cable from the positive (+) auxiliary battery terminal to terminal 5 and the negative (-) auxiliary battery terminal to terminal 6, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.

OK:

Mirror becomes warm.

If the result is not as specified, replace the outer rear view mirror assembly RH.

3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Panoramic View Monitor System)

(a) Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.

(1) Disconnect the outer rear view mirror assembly LH connector.

*a	Component without harness connected (Outer Rear View Mirror Assembly LH)

(2) Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:

Auxiliary Battery Connection	Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MV) Auxiliary battery negative (-) → Terminal 2 (M+)	Turns upward
Auxiliary battery positive (+) → Terminal 2 (M+) Auxiliary battery negative (-) → Terminal 3 (MV)	Turns downward
Auxiliary battery positive (+) → Terminal 1 (MH) Auxiliary battery negative (-) → Terminal 2 (M+)	Turns left
Auxiliary battery positive (+) → Terminal 2 (M+) Auxiliary battery negative (-) → Terminal 1 (MH)	Turns right

If the result is not as specified, replace the outer rear view mirror assembly LH.

(b) Check the operation of the mirror heater.

(1) Disconnect the outer rear view mirror assembly LH connector.

*a	Component without harness connected (Outer Rear View Mirror Assembly LH)

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
5 (+) - 6 (-)	25°C (77°F)	10 to 17 Ω

If the result is not as specified, replace the outer rear view mirror assembly LH.

(3) Connect a cable from the positive (+) auxiliary battery terminal to terminal 5 and the negative (-) auxiliary battery terminal to terminal 6, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.

OK:

Mirror becomes warm.

If the result is not as specified, replace the outer rear view mirror assembly LH.

4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Panoramic View Monitor System)

(a) Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.

(1) Disconnect the outer rear view mirror assembly LH connector.

*a	Component without harness connected (Outer Rear View Mirror Assembly LH)

(2) Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:

Auxiliary Battery Connection	Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MV) Auxiliary battery negative (-) → Terminal 2 (M+)	Turns upward
Auxiliary battery positive (+) → Terminal 2 (M+) Auxiliary battery negative (-) → Terminal 3 (MV)	Turns downward
Auxiliary battery positive (+) → Terminal 1 (MH) Auxiliary battery negative (-) → Terminal 2 (M+)	Turns left
Auxiliary battery positive (+) → Terminal 2 (M+) Auxiliary battery negative (-) → Terminal 1 (MH)	Turns right

If the result is not as specified, replace the outer rear view mirror assembly LH.

(b) Check the operation of the mirror heater.

(1) Disconnect the outer rear view mirror assembly LH connector.

*a	Component without harness connected (Outer Rear View Mirror Assembly LH)

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
5 (+) - 6 (-)	25°C (77°F)	10 to 17 Ω

If the result is not as specified, replace the outer rear view mirror assembly LH.

(3) Connect a cable from the positive (+) auxiliary battery terminal to terminal 5 and the negative (-) auxiliary battery terminal to terminal 6, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.

OK:

Mirror becomes warm.

If the result is not as specified, replace the outer rear view mirror assembly LH.

Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

(a) Engage the 2 guides and claw.

(b) Install the outer rear view mirror assembly with cover with the 3 nuts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

2. INSTALL OUTER MIRROR INSTALL HOLE COVER

(a) Engage the clip and 2 claws.

(b) Install the outer mirror install hole cover with the screw.

(d) Connect the connector.

3. INSTALL HOLE PLUG

(a) Install the hole plug.

4. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

5. INSTALL COURTESY LIGHT ASSEMBLY

Click here

6. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

7. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

8. INSTALL FRONT DOOR TRIM POCKET COVER

Click here

9. INSTALL FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here

10. PERFORM CALIBRATION (w/ Panoramic View Monitor System)

for Gasoline Model:

Click here

for HV Model:

Click here

Reassembly

REASSEMBLY

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. INSTALL SIDE TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)

Click here

2. INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY

Click here

3. INSTALL VISOR HOUSING

(a) Engage the 5 claws as shown in the illustration.

Install in this Direction

(b) Using a T20 "TORX" driver, install the visor housing with the 3 screws.

4. INSTALL OUTER MIRROR COVER

Click here

5. INSTALL OUTER MIRROR

Click here

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during outer rear view mirror assembly with cover removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Side television camera assembly LH Outer rear view mirror assembly LH Side television camera assembly RH Outer rear view mirror assembly RH	Side television camera view adjustment	Panoramic view monitor system

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Side television camera assembly LH Outer rear view mirror assembly LH Side television camera assembly RH Outer rear view mirror assembly RH	Side television camera view adjustment	Panoramic view monitor system

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here

2. REMOVE FRONT DOOR TRIM POCKET COVER

Click here

3. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

4. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

5. REMOVE COURTESY LIGHT ASSEMBLY

Click here

6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

7. REMOVE HOLE PLUG

(a) Remove the hole plug.

8. REMOVE OUTER MIRROR INSTALL HOLE COVER

(a) Disconnect the connector.

(b) Disengage the clamp.

(d) Disengage the clip and 2 claws to remove the outer mirror install hole cover.

9. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

(a) Disengage the clamp.

*a	Clamp
*b	Guide

(b) Remove the 3 nuts.

Outer Rear View Mirror Glass

Power Mirror Control System(for Gasoline Model With Memory)

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Automatic Transaxle System: Pressure Control Solenoid "A" Actuator Stuck Off (P07457F)
DESCRIPTION Based on signals from the transmission revolution sensors (NT and NC), the actual gear is detected. The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical malfunctions of the solenoid valves, transmission valve body assembly and automatic transaxl ...