Components
COMPONENTS
ILLUSTRATION
|
*A | w/o Front No. 3 Speaker |
*B | w/ Front No. 3 Speaker |
|
*1 | AUTOMATIC LIGHT CONTROL SENSOR |
*2 | FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
|
*3 | FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
*4 | FRONT PILLAR GARNISH LH |
|
*5 | FRONT PILLAR GARNISH RH |
*6 | NO. 1 DEFROSTER NOZZLE GARNISH |
|
*7 | CLIP |
- | - |
|
● | Non-reusable part |
- | - |
Installation
INSTALLATION
PROCEDURE
1. INSTALL AUTOMATIC LIGHT CONTROL SENSOR
(a) Engage the 2 claws to install the automatic light control sensor.
2. INSTALL NO. 1 DEFROSTER NOZZLE GARNISH
Click here 
3. INSTALL FRONT PILLAR GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here
4. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Click here
5. INSTALL FRONT PILLAR GARNISH LH
Click here
6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT AUTOMATIC LIGHT CONTROL SENSOR
| (a) Disconnect the G23 automatic light control sensor connector. |
 |
|
*a | Front view of wire harness connector
(to Automatic Light Control Sensor) | | |
(b) Measure the voltage and resistance according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection | Condition |
Specified Condition |
|
*1: for HV Model
*2: for Gasoline Model |
|
G23-1 (CLTB) - G23-2 (CLTE) |
Power switch off*1 |
Below 1 V |
|
Engine switch off*2 |
|
Power switch on (IG)*1 |
11 to 14 V |
|
Engine switch on (IG)*2 |
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|
G23-2 (CLTE) - Body ground |
Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
(c) Connect the G23 automatic light control sensor connector.
(d)
Connect an oscilloscope to terminals G23-2 (CLTE) and G23-4 (CLTS) of
the automatic light control sensor connector and check the waveform.
|
*a | Component with harness connected
(Automatic Light Control Sensor) |
*b | Waveform |
OK:
|
Tester Connection | Condition |
Tool Setting | Specified Condition |
|
*1: for HV Model
*2: for Gasoline Model |
|
G23-2 (CLTE) - G23-4 (CLTS) |
Power switch on (IG)*1 |
2 V/DIV., 10 ms./DIV. |
Pulse generation (See waveform) |
|
Engine switch on (IG)*2 |
HINT:
The communication waveform changes according to the surrounding brightness.
If the result is not as specified, the automatic light control sensor may be malfunctioning.
Removal
REMOVAL
PROCEDURE
1. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here 
2. REMOVE FRONT PILLAR GARNISH LH
Click here
3. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
4. REMOVE FRONT PILLAR GARNISH RH
HINT:
Use the same procedure as for the LH side.
5. REMOVE NO. 1 DEFROSTER NOZZLE GARNISH
Click here
6. REMOVE AUTOMATIC LIGHT CONTROL SENSOR
| (a) Disengage the 2 claws to remove the automatic light control sensor. |
|
