Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After
turning the engine switch (for Gasoline Model) or power switch (for HV
Model) off, waiting time may be required before disconnecting the cable
from the negative (-) auxiliary battery terminal. Therefore, make sure
to read the disconnecting the cable from the negative (-) auxiliary
battery terminal notices before proceeding with work.
Click here
2. INSTALL REAR DOOR BELT MOULDING ASSEMBLY
(a) Engage the 7 claws to install a new rear door belt moulding assembly as shown in the illustration.
 |
Install in this Direction |
3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Click here
4. INSTALL REAR DOOR REAR GUIDE SEAL
Click here
5. CONNECT REAR DOOR WEATHERSTRIP
Click here
6. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Click here
7. INSTALL REAR DOOR GLASS RUN
Click here
8. INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER
Click here
9. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP
Click here
10. INSTALL REAR DOOR SERVICE HOLE COVER
Click here
11. INSTALL REAR DOOR NO. 1 TRIM BRACKET
Click here
12. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
14. INSTALL REAR DOOR TRIM ASSEMBLY COVER
Click here
15. INSTALL REAR DOOR ARMREST COVER SUB-ASSEMBLY
Click here
16. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
17. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
18. INITIALIZE POWER WINDOW CONTROL SYSTEM
for Gasoline Model:
Click here
for HV Model:
Click here
19. INSPECT POWER WINDOW OPERATION
for Gasoline Model:
Click here
for HV Model:
Click here
Removal
REMOVAL
CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization, or
registration) that must be performed after parts are removed and
installed, or replaced during rear door belt moulding assembly
removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here  |
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for Gasoline Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
- Rear door glass sub-assembly
- Rear door glass run
| Initialize power window control system |
- Auto up and down function
- Jam protection function
- Remote control function
- Key-linked function
- Wireless transmitter-linked function
- Key-off operation function
- Catch protection function
- Window open warning function
|
|
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for HV Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
- Rear door glass sub-assembly
- Rear door glass run
| Initialize power window control system |
- Auto up and down function
- Jam protection function
- Remote control function
- Key-linked function
- Wireless transmitter-linked function
- Key-off operation function
- Catch protection function
- Window open warning function
|
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After
turning the engine switch (for Gasoline Model) or power switch (for HV
Model) off, waiting time may be required before disconnecting the cable
from the negative (-) auxiliary battery terminal. Therefore, make sure
to read the disconnecting the cable from the negative (-) auxiliary
battery terminal notices before proceeding with work.
Click here
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
4. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY
Click here
5. REMOVE REAR DOOR TRIM ASSEMBLY COVER
Click here
6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
8. REMOVE REAR DOOR NO. 1 TRIM BRACKET
Click here
9. REMOVE REAR DOOR SERVICE HOLE COVER
Click here
10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
Click here
11. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER
Click here
12. REMOVE REAR DOOR GLASS RUN
Click here
13. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Click here
14. DISCONNECT REAR DOOR WEATHERSTRIP
Click here
15. REMOVE REAR DOOR REAR GUIDE SEAL
Click here
16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Click here
17. REMOVE REAR DOOR BELT MOULDING ASSEMBLY
(a) Apply protective tape around the rear door belt moulding assembly as shown in the illustration.
 |
Protective Tape |
(b) Disengage the 7 claws to remove the rear door belt moulding assembly as shown in the illustration.
 |
Remove in this Direction |
