Toyota Avalon (XX50): Rear Bumper

Components

COMPONENTS

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

*A	for HV Model	-	-
*1	REAR BUMPER ENERGY ABSORBER	*2	REAR BUMPER REINFORCEMENT
*3	REAR BUMPER SIDE RETAINER LH	*4	REAR BUMPER SIDE RETAINER RH
*5	REAR BUMPER SIDE SEAL LH	*6	REAR BUMPER SIDE SEAL RH
*7	REAR BUMPER UPPER RETAINER LH	*8	REAR BUMPER UPPER RETAINER RH
*9	REAR COMBINATION LIGHT ASSEMBLY LH	*10	REAR COMBINATION LIGHT ASSEMBLY RH
*11	GROMMET	-	-
	N*m (kgf*cm, ft.*lbf): Specified torque	●	Non-reusable part

Disassembly

DISASSEMBLY

PROCEDURE

1. REMOVE REAR CENTER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

Click here

HINT:

Use the same procedure for the RH side and LH side.

2. REMOVE REAR CORNER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

Click here

HINT:

Use the same procedure for the RH side and LH side.

3. REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

Click here

HINT:

Use the same procedure for the RH side and LH side.

4. REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

Click here

HINT:

Use the same procedure for the RH side and LH side.

5. REMOVE FOG LIGHT SEAL (w/ Intuitive Parking Assist System)

(a) Remove the 5 fog light seals.

6. REMOVE NO. 2 LUGGAGE ROOM WIRE (w/ Intuitive Parking Assist System)

7. REMOVE REFLEX REFLECTOR ASSEMBLY LH

(a) Remove the screw.

(b) Disengage the 2 guides to remove the reflex reflector assembly LH as shown in the illustration.

	Remove in this Direction (1)
	Remove in this Direction (2)

8. REMOVE REFLEX REFLECTOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

9. REMOVE LOWER REAR BUMPER COVER

(a) Remove the 2 clips (A).

(b) Remove the 4 clips (B).

(c) Disengage the 14 claws and 2 guides to remove the lower rear bumper cover.

10. REMOVE REAR BUMPER SIDE RETAINER LH

(a) Remove the screw.

(b) Disengage the 3 clips as shown in the illustration.

Remove in this Direction

(c) Disengage the 2 claws as shown in the illustration.

	Remove in this Direction (1)
	Remove in this Direction (2)

(d) Disengage the guide to remove the rear bumper side retainer LH.

11. REMOVE REAR BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.

12. REMOVE SPARE WHEEL COVER ASSEMBLY

Click here

13. REMOVE BAGGAGE HOLDER NET

Click here

14. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Click here

15. REMOVE REAR FLOOR FINISH PLATE

Click here

16. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD

Click here

17. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

18. REMOVE LUGGAGE COMPARTMENT TRIM INNER COVER RH

for Gasoline Model: Click here

for HV Model: Click here

19. REMOVE LUGGAGE COMPARTMENT TRIM INNER COVER LH

Click here

20. REMOVE REAR BUMPER UPPER RETAINER LH

(a) Remove the rear combination light assembly LH.

Click here

(b) Remove the screw and rear bumper upper retainer LH.

21. REMOVE REAR BUMPER UPPER RETAINER RH

HINT:

Use the same procedure as for the LH side.

22. REMOVE REAR BUMPER SIDE SEAL LH

(a) Remove the 2 grommets.

(b) Remove the 2 clips and rear bumper side seal LH.

23. REMOVE REAR BUMPER SIDE SEAL RH

(a) Remove the 2 grommets.

(b) for Gasoline Model: (1) Remove the 2 clips and rear bumper side seal RH.

*A for HV Model

(c) for HV Model:

(1) Remove the 3 clips and rear bumper side seal RH.

24. REMOVE REAR BUMPER ENERGY ABSORBER

(a) Disengage the 2 guides to remove the rear bumper energy absorber as shown in the illustration.

Remove in this Direction

25. REMOVE REAR BUMPER REINFORCEMENT

(a) Remove the 6 bolts and rear bumper reinforcement.

Installation

INSTALLATION

PROCEDURE

1. INSTALL REAR BUMPER ASSEMBLY

(a) w/ Intuitive Parking Assist System:

Install in this Direction

(1) Connect the connector.

(b) Engage the 6 claws as shown in the illustration.

(c) Engage the 6 claws as shown in the illustration.

Install in this Direction

HINT:

Use the same procedure for the RH side and LH side.

(d) for Gasoline Model:

(1) Install the 8 clips.

(e) for HV Model:

(1) Install the 9 clips.

(f) Install the clip.

HINT:

Use the same procedure for the RH side and LH side.

(g) Install the rear bumper assembly with the 2 screws.

2. INSTALL REAR COMBINATION LIGHT COVER LH

Click here

3. INSTALL REAR COMBINATION LIGHT COVER RH

HINT:

Use the same procedure as for the LH side.

4. PERFORM CALIBRATION (w/ Intelligent Clearance Sonar System)

for HV Model:

Click here

for Gasoline Model:

Click here

Reassembly

REASSEMBLY

PROCEDURE

1. INSTALL REAR BUMPER REINFORCEMENT

(a) Install the rear bumper reinforcement with the 6 bolts. Torque: 29 N·m {296 kgf·cm, 21 ft·lbf}

2. INSTALL REAR BUMPER ENERGY ABSORBER

(a) Engage the 2 guides to install the rear bumper energy absorber as shown in the illustration.

Install in this Direction

3. INSTALL REAR BUMPER SIDE SEAL LH

(a) Install the 2 clips.

(b) Install the rear bumper side seal LH with 2 new grommets.

4. INSTALL REAR BUMPER SIDE SEAL RH

(a) for Gasoline Model: (1) Install the 2 clips.

*A for HV Model

(b) for HV Model:

(1) Install the 3 clips.

(c) Install the rear bumper side seal RH with 2 new grommets.

5. INSTALL REAR BUMPER UPPER RETAINER LH

(a) Engage the 2 guides to temporarily install the rear bumper upper retainer LH to the rear combination light assembly LH.

(b) Engage the grommet.

(c) Engage the guide and pin as shown in the illustration to temporarily install the rear bumper upper retainer LH and rear combination light assembly LH as a set.

*a	Pin
*b	Guide
	Install in this Direction

(d) Install the rear combination light assembly with the 2 screws (A).

(e) Engage the clamp.

(f) Connect the connector.

(g) Install the rear bumper upper retainer LH with the screw (B).

6. INSTALL REAR BUMPER UPPER RETAINER RH

HINT:

Use the same procedure as for the LH side.

7. INSTALL LUGGAGE COMPARTMENT TRIM INNER COVER LH

Click here

8. INSTALL LUGGAGE COMPARTMENT TRIM INNER COVER RH

Click here

9. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)

Click here

10. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD

Click here

11. INSTALL REAR FLOOR FINISH PLATE

Click here

12. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Click here

13. INSTALL BAGGAGE HOLDER NET

Click here

14. INSTALL SPARE WHEEL COVER ASSEMBLY

Click here

15. INSTALL REAR BUMPER SIDE RETAINER LH

(a) Engage the guide as shown in the illustration.

	Install in this Direction (1)
	Install in this Direction (2)

(b) Engage the 2 claws as shown in the illustration.

(c) Engage the 3 clips as shown in the illustration.

Install in this Direction

(d) Install the rear bumper side retainer LH with the screw.

16. INSTALL REAR BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.

17. INSTALL LOWER REAR BUMPER COVER

(a) Engage the 2 guides and 14 claws.

(b) Install the 2 clips (A).

(c) Install the lower rear bumper cover with the 4 clips (B).

18. INSTALL REFLEX REFLECTOR ASSEMBLY LH

(a) Engage the 2 guides as shown in the illustration.

	Install in this Direction (1)
	Install in this Direction (2)

(b) Install the reflex reflector assembly LH with the screw.

19. INSTALL REFLEX REFLECTOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

20. INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ Intuitive Parking Assist System)

21. INSTALL FOG LIGHT SEAL (w/ Intuitive Parking Assist System)

HINT:

When installing the fog light seals, heat the rear bumper cover using a heat light.

CAUTION:

• Do not touch the heat light and heated parts, touching the heat light may result in burns.
• Touching heated parts for a long time may result in burns.

NOTICE:

Do not heat the rear bumper cover excessively.

(a) Clean the rear bumper cover surface.

(1) Using a heat light, heat the rear bumper cover surface.

(2) Remove any remaining double-sided tape from the rear bumper cover.

(3) Wipe off any tape adhesive residue with cleaner.

(b) Remove the release paper from 5 new fog light seals.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.

(c) Install the 5 fog light seals as shown in the illustration.

HINT:

Press the fog light seal firmly to install it.

22. INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

Click here

HINT:

Use the same procedure for the RH side and LH side.

23. INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

Click here

HINT:

Use the same procedure for the RH side and LH side.

24. INSTALL REAR CORNER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

Click here

HINT:

Use the same procedure for the RH side and LH side.

25. INSTALL REAR CENTER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

Click here

HINT:

Use the same procedure for the RH side and LH side.

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear bumper assembly removal/installation are shown below.

HINT:

If the bumper is damaged, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (frame, stud bolt) to make sure it is not dented or bent.

Click here

If the visual inspection finds a problem, check the installation condition of the blind spot monitor sensor, and adjust the installation position of the blind spot monitor sensor as necessary.

PROCEDURE

1. REMOVE REAR COMBINATION LIGHT COVER LH

Click here

2. REMOVE REAR COMBINATION LIGHT COVER RH

HINT:

Use the same procedure as for the LH side.

3. REMOVE REAR BUMPER ASSEMBLY

(a) Apply protective tape around the rear bumper assembly as shown in the illustration.

Protective Tape

(b) Remove the 2 screws.

(c) Remove the clip. HINT: Use the same procedure for the RH side and LH side.

(d) for Gasoline Model:

(1) Remove the 8 clips.

(e) for HV Model:

(1) Remove the 9 clips.

(f) Disengage the 6 claws as shown in the illustration.

Remove in this Direction

HINT:

Use the same procedure for the RH side and LH side.

(g) Disengage the 6 claws to remove the rear bumper assembly as shown in the illustration.

Remove in this Direction

(h) w/ Intuitive Parking Assist System:

(1) Disconnect the connector to remove the rear bumper assembly.