Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE LUGGAGE COMPARTMENT DOOR OPENER SYSTEM
HINT:
The following items can be customized.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
(a) Customizing with the Techstream
(1) Connect the Techstream to the DLC3.
(2) Turn the power switch on (IG).
(3) Turn the Techstream on.
(4) Enter the following menus: Customize Setting / Door Lock.
(5) Select the setting by referring to the table below.
Door Lock
|
Tester Display | Description |
Default | Setting |
ECU |
| Trunk Link with Door Lock |
Function
that opens the luggage compartment door when the luggage electrical key
switch is pressed and all doors are unlocked using the entry door lock
function, wireless door lock function, mechanical key or door control
switch. | ON |
0:OFF,1:ON | Main body ECU (Multiplex network body ECU) |
Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In
the table below, the values listed under "Normal Condition" are
reference values. Do not depend solely on these reference values when
deciding whether a part is faulty or not.
HINT:
Using
the Techstream to read the Data List allows the values or states of
switches, sensors, actuators and other items to be read without removing
any parts. This non-intrusive inspection can be very useful because
intermittent conditions or signals may be discovered before parts or
wiring is disturbed. Reading the Data List information early in
troubleshooting is one way to save diagnostic time.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (desired system) / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|
Trunk Lock Position | Luggage compartment door lock signal |
Lock or Unlock | Lock: Luggage compartment door lock assembly locked
Unlock: Luggage compartment door lock assembly unlocked |
- |
| Trunk/BDoor Open SW |
Luggage compartment door opening switch signal |
OFF or ON | OFF: Luggage compartment door opening switch off
ON: Luggage compartment door opening switch on |
- |
| Luggage Courtesy SW |
Luggage compartment door courtesy light switch signal |
OFF or ON | OFF: Luggage compartment door courtesy light switch off
ON: Luggage compartment door courtesy light switch on |
- |
Body Electrical > Smart Key > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|
Tr/B-Door Unlock SW | Luggage electrical key switch |
OFF or ON | OFF: Luggage electrical key switch not pressed
ON: Luggage electrical key switch pressed |
When this item is abnormal, there is a malfunction in the luggage electrical key switch or related parts. |
ACTIVE TEST
HINT:
Using
the Techstream to perform the Active Tests allows relays, VSVs and
actuators and other items to be operated without removing any parts.
This non-intrusive functional inspection can be very useful because
intermittent operation may be discovered before parts or wiring is
disturbed. Performing Active Tests early in troubleshooting is one way
to save diagnostic time. Data List information can be displayed while
performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Main Body > Active Test
|
Tester Display | Measurement Item |
Control Range | Diagnostic Note |
|
Trunk and Back-Door Open |
Operate luggage compartment door lock assembly latch release |
OFF or ON | - |
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the luggage compartment door opener system.
- *: Use the Techstream.
PROCEDURE
|
1. | VEHICLE BROUGHT TO WORKSHOP |
|
NEXT |
 | |
| 2. |
CUSTOMER PROBLEM ANALYSIS |
HINT:
- In troubleshooting, confirm that the problem symptoms have been
accurately identified. Preconceptions should be discarded in order to
make an accurate judgment. To clearly understand what the problem
symptoms are, it is extremely important to ask the customer about the
problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points for problem analysis:
|
What |
Vehicle model, system name |
|
When |
Date, time, occurrence frequency |
|
Where |
Road conditions |
|
Under what conditions? |
Driving conditions, weather conditions |
|
How did it happen? |
Problem symptoms |
|
NEXT | |
| |
(a) Measure the auxiliary battery voltage with the power switch off.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
(b) Check the fuses and relays.
(c)
Check the connector connections and terminals to make sure that there
are no abnormalities such as loose connections, deformation, etc.
|
NEXT | |
| |
| 4. |
CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for CAN communication system DTCs.
Click here
|
Result | Proceed to |
|
CAN DTCs are not output |
A |
| CAN DTCs are output |
B |
| B |
 | GO TO CAN COMMUNICATION SYSTEM |
|
A | |
| |
| 5. |
PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
|
Result | Proceed to |
|
Fault is not listed in Problem Symptoms Table |
A |
| Fault is listed in Problem Symptoms Table |
B |
| B |
| GO TO STEP 7 |
|
A | |
| |
| 6. |
OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Operation Check
Click here
(b) Terminals of ECU
Click here
(c) Data List / Active Test
Click here
(d) Inspection
|
NEXT | |
| |
|
NEXT | |
| |
| NEXT |
| END |
Luggage Compartment Door Opener does not Operate
DESCRIPTION
The main body
ECU (multiplex network body ECU) receives switch signals from the
luggage compartment door opening switch assembly and operates the
luggage compartment door lock assembly to open the luggage compartment
door.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- The luggage compartment door opener system uses the CAN communication
system. First, confirm that there is no malfunction in the CAN
communication system. Refer to the How to Proceed with Troubleshooting
procedure.
Click here 
- Before replacing the main body ECU (multiplex network body ECU) or
certification ECU (smart key ECU assembly), refer to Registration.
Click here
PROCEDURE
|
1. | CHECK POWER DOOR LOCK CONTROL SYSTEM |
(a) Check power door lock control system operation.
Click here
OK:
Power door lock control system is normal.
| NG |
 | GO TO POWER DOOR LOCK CONTROL SYSTEM |
|
OK |
 | |
| 2. |
CHECK WIRELESS DOOR LOCK CONTROL SYSTEM |
(a) Check wireless door lock control system operation.
Click here
OK:
Wireless door lock control system is normal.
| NG |
| GO TO WIRELESS DOOR LOCK CONTROL SYSTEM |
|
OK | |
| |
| 3. |
PERFORM ACTIVE TEST USING TECHSTREAM (Trunk and Back-Door Open) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Main Body > Active Test
|
Tester Display | Measurement Item |
Control Range | Diagnostic Note |
|
Trunk and Back-Door Open |
Operate luggage compartment door lock assembly latch release |
OFF or ON | - |
Body Electrical > Main Body > Active Test
|
Tester Display |
| Trunk and Back-Door Open |
OK:
Luggage compartment door lock assembly latch release motor operates normally.
| NG |
| GO TO STEP 9 |
|
OK | |
| |
| 4. |
READ VALUE USING TECHSTREAM (Trunk/BDoor Open SW, Luggage Courtesy SW) |
(a) Enter the following menus: Body Electrical / Main Body / Data List.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|
Trunk/BDoor Open SW | Luggage compartment door opening switch signal |
OFF or ON | OFF: Luggage compartment door opening switch off
ON: Luggage compartment door opening switch on |
- |
| Luggage Courtesy SW |
Luggage compartment door courtesy light switch signal |
OFF or ON | OFF: Luggage compartment door courtesy light switch off
ON: Luggage compartment door courtesy light switch on |
- |
Body Electrical > Main Body > Data List
|
Tester Display |
| Trunk/BDoor Open SW |
|
Luggage Courtesy SW |
OK:
The
Techstream display changes correctly in response to the ON/OFF
operation of the luggage compartment door opening switch or luggage
compartment door courtesy light switch.
|
Result | Proceed to |
|
OK | A |
|
NG (Trunk/BDoor Open SW) |
B |
| NG (Luggage Courtesy SW) |
C |
| B |
| GO TO STEP 7 |
| C |
| GO TO LIGHTING SYSTEM |
|
A | |
| |
| 5. |
READ VALUE USING TECHSTREAM (Tr/B-Door Unlock SW) |
(a) Enter the following menus: Body Electrical / Smart Key / Data List.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data List
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|
Tr/B-Door Unlock SW | Luggage electrical key switch |
OFF or ON | OFF: Luggage electrical key switch not pressed
ON: Luggage electrical key switch pressed |
When this item is abnormal, there is a malfunction in the luggage electrical key switch or related parts. |
OK:
The Techstream display changes correctly in response to the operation of the luggage electrical key switch.
| NG |
| GO TO SMART KEY SYSTEM (for Entry Function) |
|
OK | |
| |
| 6. |
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
(a) Temporarily replace the main body ECU (multiplex network body ECU) with a new or known good one.
Click here
(b) Check that the luggage door opener system is normal.
| OK |
| END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) |
| NG |
| REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| 7. |
INSPECT LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY |
(a) Remove the luggage compartment door opening switch assembly.
Click here
(b) Inspect the luggage compartment door opening switch assembly.
Click here
| NG |
| REPLACE LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY |
|
OK | |
| |
| 8. |
CHECK
HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) -
LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY AND BODY GROUND) |
(a) Disconnect the G34 main body ECU (multiplex network body ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|
G34-4 (TSW) - G28-5 (B) |
Always | Below 1 Ω |
|
G28-2 (L) - Body ground |
Always | Below 1 Ω |
|
G34-4 (TSW) or G28-5 (B) - Body ground |
Always | 10 kΩ or higher |
| OK |
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG |
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 9. |
INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY |
(a) Remove the luggage compartment door lock assembly.
Click here
(b) Inspect the luggage compartment door lock assembly.
Click here
| NG |
| REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY |
|
OK | |
| |
| 10. |
CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND) |
(a) Disconnect the 4H instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|
P3-3 (D+) - 4H-34 | Always |
Below 1 Ω |
|
P3-1 (B) - 4H-20 | Always |
Below 1 Ω |
|
P3-2 (E) - Body ground |
Always | Below 1 Ω |
|
P3-3 (D+) or 4H-34 - Body ground |
Always | 10 kΩ or higher |
|
P3-1 (B) or 4H-20 - Body ground |
Always | 10 kΩ or higher |
| NG |
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
OK | |
| |
| 11. |
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
(a) Temporarily replace the instrument panel junction block assembly with a new or known good one.
Click here
(b) Check that the luggage door opener system is normal.
| OK |
| END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE) |
| NG |
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
Operation Check
OPERATION CHECK
BASIC FUNCTION INSPECTION
(a) When the luggage compartment door opening switch assembly is pressed, check that the luggage compartment door unlatches.
Parts Location
PARTS LOCATION
ILLUSTRATION
|
*1 | LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY |
*2 | DLC3 |
|
*3 | MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
*4 | INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
- DOOR BACK RELAY - TRUNK OPN FUSE |
|
*5 | CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
- | - |
ILLUSTRATION
|
*1 | LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY |
*2 | LUGGAGE ELECTRICAL KEY SWITCH |
Precaution
PRECAUTION
PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
NOTICE:
When
disconnecting the cable from the negative (-) auxiliary battery
terminal, initialize the following systems after the cable is
reconnected.
|
System Name | See Procedure |
|
Lane Departure Alert System (w/ Steering Control) |
 |
|
Intelligent Clearance Sonar System |
|
Parking Assist Monitor System |
|
Panoramic View Monitor System |
|
Pre-collision System |
|
Lighting System (for HV Model with Cornering Light) |
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
- Use the table below to help determine the cause of problem symptoms. If
multiple suspected areas are listed, the potential causes of the
symptoms are listed in order of probability in the "Suspected Area"
column of the table. Check each symptom by checking the suspected areas
in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Luggage Compartment Door Opener System |
Symptom | Suspected Area |
Link |
| Luggage door opener does not operate |
Proceed to "Luggage Compartment Door Opener does not Operate" |
 |
System Description
SYSTEM DESCRIPTION
LUGGAGE COMPARTMENT DOOR OPENER SYSTEM DESCRIPTION
(a)
If the luggage compartment door opening switch assembly is pressed and
the luggage compartment door is closed, a luggage compartment door lock
assembly open operation signal is sent to the main body ECU (multiplex
network body ECU). Then the main body ECU (multiplex network body ECU)
unlatches the luggage compartment door.
FUNCTION OF MAIN COMPONENTS
|
Item | Outline |
|
Luggage compartment door opening switch assembly |
Turns the luggage compartment door opener system ON/OFF |
|
Luggage compartment door lock assembly |
Opens the luggage compartment door via a signal from the main body ECU (multiplex network body ECU) |
|
Main body ECU (Multiplex network body ECU) |
Receives a luggage compartment door lock assembly open operation signal, and controls the luggage compartment door opener system |
System Diagram
SYSTEM DIAGRAM
Luggage Compartment Door Opener System
Communication Table |
Sender | Receiver |
Signal | Line |
|
Certification ECU (Smart Key ECU Assembly) |
Main Body ECU (Multiplex Network Body ECU) |
Luggage compartment door lock assembly open operation signal |
CAN |
Terminals Of Ecu
TERMINALS OF ECU
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here 
(b) Measure the resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connectors disconnected.
|
Terminal No. (Symbol) | Wiring Color |
Terminal Description | Condition |
Specified Condition |
|
G32-19 (GND2) - Body ground |
W-B - Body ground | Ground |
Always | Below 1 Ω |
(c) Reconnect the instrument panel junction block assembly connectors.
(d) Measure the resistance and voltage according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connectors disconnected.
|
Terminal No. (Symbol) | Wiring Color |
Terminal Description | Condition |
Specified Condition |
|
MB-11 (GND1) - Body ground |
- | Ground |
Always | Below 1 Ω |
|
MB-31 (BECU) - Body ground |
- | Auxiliary battery power supply |
Power switch off | 11 to 14 V |
|
MB-30 (ACC) - Body ground |
- | ACC power supply |
Power switch on (ACC) |
11 to 14 V |
|
MB-30 (ACC) - Body ground |
- | ACC power supply |
Power switch off | Below 1 V |
|
MB-32 (IG) - Body ground |
- | IG power supply |
Power switch on (IG) |
11 to 14 V |
|
MB-32 (IG) - Body ground |
- | IG power supply |
Power switch off | Below 1 V |
(e) Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.
Click here
(f) Measure the voltage and check for pulses according to the value(s) in the table below.
|
Terminal No. (Symbol) | Wiring Color |
Terminal Description | Condition |
Specified Condition |
|
G34-4 (TSW) - Body ground |
LG - Body ground |
Luggage compartment door opening switch signal |
Luggage compartment door opening switch on |
Below 1 V |
|
Power switch off, all doors closed and luggage compartment door opening switch off |
Pulse generation |
|
4H-34 (LGCY) - Body ground |
LA-GR - Body ground |
Luggage compartment door courtesy light switch assembly input signal |
Luggage compartment door open |
Below 1 V |
|
Luggage compartment door closed |
11 to 14 V |
|
4H-20 (TR+) - Body ground |
LA-G - Body ground |
Luggage compartment door open relay output signal |
Luggage compartment door opening switch on |
11 to 14 V |
|
Luggage compartment door opening switch off |
Below 1 V |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Click here
