Components
COMPONENTS
ILLUSTRATION
|
*1 | SPARE WHEEL COVER ASSEMBLY |
- | - |
ILLUSTRATION
|
*1 | BAGGAGE HOLDER NET |
*2 | LUGGAGE COMPARTMENT INNER TRIM PAD |
|
*3 | NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
*4 | REAR FLOOR FINISH PLATE |
ILLUSTRATION
|
*1 | LUGGAGE COMPARTMENT TRIM INNER COVER LH |
- | - |
ILLUSTRATION
|
*1 | FUEL FILLER OPENING LID LOCK RETAINER |
*2 | FUEL LID LOCK WITH MOTOR ASSEMBLY |
 |
MP grease | - |
- |
Inspection
INSPECTION
PROCEDURE
1. INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY
(a) Check the operation of the fuel lid lock with motor assembly (motor operation).
(1)
Apply auxiliary battery voltage to the fuel lid lock with motor
assembly connector, and check the operation of the fuel lid lock with
motor assembly.
|
*a | Component without harness connected
(Fuel Lid Lock with Motor Assembly) |
*b | Shaft Stroke |
|
*c | Lever |
*d | Shaft |
OK:
|
Auxiliary Battery Connection |
Specified Condition |
|
Auxiliary battery positive (+) → Terminal 1 Auxiliary battery negative (-) → Terminal 2 |
Shaft retracts |
If the result is not as specified, replace the fuel lid lock with motor assembly.
(b) Check the operation of the fuel lid lock with motor assembly (fuel lid courtesy switch).
(1) Measure the resistance according the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|
2 - 3 | Shaft not pushed (On) |
Below 1 Ω |
|
2 - 3 | Shaft pushed (Off) |
10 kΩ or higher |
If the result is not as specified, replace the fuel lid lock with motor assembly.
(c) Measure the shaft stroke.
Standard:
|
Area | Condition |
Specified Condition |
|
Shaft stroke | Lever pulled |
16.05 mm (0.632 in.) |
If the result is not as specified, replace the fuel lid lock with motor assembly.
Installation
INSTALLATION
PROCEDURE
1. INSTALL FUEL LID LOCK WITH MOTOR ASSEMBLY
(a) Apply MP grease to the sliding parts of the fuel lid lock with motor assembly.
(b) Connect the connector.
(c) Engage the 2 claws.
(d) Engage the clamp to install the fuel lid lock with motor assembly.
2. INSTALL FUEL FILLER OPENING LID LOCK RETAINER
(a) Install the fuel filler opening lid lock retainer as indicated by the arrows, the order shown in the illustration.
 |
Install in this Direction (1) |
 |
Turn in this Direction (2) |
3. INSTALL LUGGAGE COMPARTMENT TRIM INNER COVER LH
Click here 
4. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD
Click here
5. INSTALL REAR FLOOR FINISH PLATE
Click here
6. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Click here
7. INSTALL SPARE WHEEL COVER ASSEMBLY
Click here
8. INSTALL BAGGAGE HOLDER NET
Click here
Removal
REMOVAL
PROCEDURE
1. REMOVE BAGGAGE HOLDER NET
Click here 
2. REMOVE SPARE WHEEL COVER ASSEMBLY
Click here
3. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Click here
4. REMOVE REAR FLOOR FINISH PLATE
Click here
5. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD
Click here
6. REMOVE LUGGAGE COMPARTMENT TRIM INNER COVER LH
Click here
7. REMOVE FUEL FILLER OPENING LID LOCK RETAINER
(a)
Turn and remove the fuel filler opening lid lock retainer as indicated
by the arrows, in the order shown in the illustration.
 |
Turn in this Direction (1) |
 |
Remove in this Direction (2) |
8. REMOVE FUEL LID LOCK WITH MOTOR ASSEMBLY
(b) Disengage the 2 claws.
(c) Disconnect the connector to remove the fuel lid lock with motor assembly.
